| Model |
DSO2D15 |
DSO2D10 |
DSO2C15 |
DSO2C10 |
| Bandwidth |
150MHz |
100MHz |
150MHz |
100MHz |
| Oscilloscope channels |
2CH |
2CH |
2CH |
2CH |
| Waveform generator |
1CH |
1CH |
– |
– |
| Oscilloscope |
| Sample rate |
1GSa/s (single channel) 500MSa/s (two channels) |
| Acquisition |
| Normal |
Sample data |
| Peak-to-peak value |
Display high frequency and random burr |
| Average |
Average waveform, times: 4, 8, 16, 32, 64, 128 |
| High resolution |
Up to 12bit |
| Input |
| Input coupling |
DC, AC, GND |
| Input impedance |
1MΩ±2% ‖20pF±3pF |
| Probe attenuation factor |
1X, 10X, 100X, 1000X |
| Voltage rating |
300V CAT II |
| Maximum input voltage |
300VRMS (10X) |
| Horizontal |
| Waveform interpolation |
(sin x)/x |
| Maximum record length |
Single channel maximum 8M |
| Two channels maximum 4M |
| Horizontal scale range |
2ns/div~100s/div 1, 2, 5 step by step |
| Time base mode |
Y-T, X-Y, Roll |
| Zero offset |
±0.5 div×minimum time base gear |
| Sample Rate and Delay Time Accuracy |
±25ppm |
| Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy |
single-shot, Normal mode ±（1 sample interval+100ppm×reading+0.6ns） |
| ＞16 times averages ±（1 sample interval+100ppm×reading+0.4ns） |
| Sample interval=sec/div÷200 |
| Sample Rate and Delay Time Accuracy |
±50ppm（at any interval greater than 1ms） |
| Vertical |
| Model |
DSO2D15 |
DSO2D10 |
DSO2C15 |
DSO2C10 |
| Bandwidth |
150MHz |
100MHz |
150MHz |
100MHz |
| Rising time in BNC position (typical) |
2.4ns |
3.5ns |
2.4ns |
3.5ns |
| Vertical resolution |
8 bits resolution, each channel samples simultaneously |
| Vertical sensitivity |
2mV/div to 10V/div |
| Offset range |
≥ 200mV/div, ±1V; |
| ＜200mV/div ±50V |
| Mathematical operation |
+, -, ×, ÷, FFT |
| FFT |
Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop |
| Bandwidth Limit |
20MHz |
| Bass response（-3db） |
In BNC position ≤ 10Hz |
| Vertical gain accuracy |
In ”normal” or ”average” acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%; |
| In ”normal” or ”average” acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4% |
| Note: Bandwidth reduced to 6MHz when using a 1X probe |
| Trigger |
| Trigger type |
Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC |
| Trigger level range |
±5 divisions from the center of the screen |
| Trigger mode |
Auto, Normal, single |
| Level |
CH1~CH2 |
±4 divisions from the center of the screen |
| EXT(Only With AWG Model) |
0~3.3V |
| Holdoff range |
8ns~10s |
| Trigger level accuracy |
CH1~CH2 |
0.2 div×volts/div within ±4 divisions from the center of the screen |
| EXT(Only With AWG Model) |
±（Set value× 6%+40mV） |
| Edge trigger |
Slope |
Rising edge, falling edge, rising or falling edge |
| Signal source |
CH1, CH2, EXT(Only With AWG Model) |
| Pulse width trigger |
Polarity |
Positive polarity, negative polarity |
| Condition(When) |
<, >, !=, = |
| Signal source |
CH1~CH2, |
| Pulse width range |
8ns ~ 10s |
| Accuracy |
8ns |
| Video trigger |
Signal standard |
NTSC, PAL |
| Signal source |
CH1~CH2 |
| Synchronization |
Scanning line, line number, odd field, even field, all field |
| Slope trigger |
Slope |
rising, falling |
| Condition(When) |
<, >, !=, = |
| Signal source |
CH1 ~ CH2 |
| Time range |
8ns ~ 10s |
| Accuracy |
8ns |
| Overtime trigger |
Signal source |
CH1~CH2， |
| Polarity |
Positive polarity, negative polarity |
| Time range |
8ns ~ 10s |
| Accuracy |
8ns |
| Window trigger |
Signal source |
CH1~CH2 |
| Pattern trigger |
Pattern |
0: low level; 1: high level; X: ignore |
| Level（signal source） |
CH1~CH2 |
| Interval trigger |
Slope |
rising, falling |
| Condition(When) |
<, >, !=, = |
| Signal source |
CH1~CH2 |
| Time range |
8ns ~ 10s |
| Accuracy |
8ns |
| Under Amp trigger |
Polarity |
Positive polarity, negative polarity |
| Condition(When) |
<, >, !=, = |
| Signal source |
CH1~CH2 |
| Time range |
8ns ~ 10s |
| Accuracy |
8ns |
| UART trigger |
Condition(When) |
Start, Stop, data, Parity ERR, COM ERR |
| Signal source(RX/TX) |
CH1~CH2 |
| Data format |
Hex (hexadecimal) |
| Data length |
1 byte |
| Data bit width |
5 bit, 6 bit, 7 bit, 8 bit |
| Odd-even check |
none, odd, even |
| Idle level |
high, low |
| Baud rate (optional) |
110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s |
| Baud rate(user-defined) |
300bit/s~334000bit/s |
| LIN trigger |
Condition(When) |
Interval field, synchronization field, ID field, synchronization error, identifier, ID and data |
| Signal source |
CH1~CH2 |
| Data format |
Hex (hexadecimal) |
| Baud rate (optional) |
110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s |
| Baud rate(user-defined) |
300bit/s~334000bit/s |
| CAN trigger |
Condition(When) |
Start bit, remote frame ID, data frame ID, frame ID, data frame data, error frame, all errors, ACK Error, overload frame |
| Signal source |
CH1~CH2 |
| Data format |
Hex (hexadecimal) |
| Baud rate (optional) |
10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000 |
| Baud rate(user-defined) |
5kbit/s~1Mbit/s |
| SPI trigger |
Signal source |
CH1~CH2 |
| Data format |
Hex (hexadecimal) |
| Data bit width |
4, 8, 16, 24, 32 |
| IIC trigger |
Signal source (SDA/SCL) |
CH1~CH2 |
| Data format |
Hex (hexadecimal) |
| Data index |
0~7 |
| When(condition) |
Start bit, stop bit, No Ack, address, restart, address and data |
| Measurement |
| Cursor |
Voltage difference between cursors △V |
| Time difference between cursors △T |
| Reciprocal of △T, in Hertz (1/△T) |
| Auto measurement |
frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, + width, – width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, + duty, – duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF |
| DVM |
Data source |
CH1, CH2 |
| Measurement type |
DC RMS |
| AC RMS |
| DC |
| Frequency meter |
hardware 6 bits frequency meter |
| Arbitrary waveform generator |
| Channel |
1 |
| Sample rate |
200MSa/s |
| Vertical resolution |
12 bits |
| Maximum frequency |
25 MHz |
| Standard waveforms |
sine, square, ramp,Exp, noise, DC |
| Arbitrary waveform |
Arb1, Arb2, Arb3, Arb4 |
| Sin |
Frequency range |
0.1Hz~25MHz |
| Square/pulse |
Frequency range |
0.1Hz~10MHz |
| Triangular wave |
Frequency range |
0.1Hz~1MHz |
| Sampling wave |
Frequency range |
0.1Hz~1MHz |
| Index |
Frequency range |
0.1Hz~5MHz |
| Noise |
|
| Arb1 |
Frequency range |
0.1 Hz to 10 MHz |
| Arb2 |
Frequency range |
0.1 Hz to 10 MHz |
| Arb3 |
Frequency range |
0.1 Hz to 10 MHz |
| Arb4 |
Frequency range |
0.1 Hz to 10 MHz |
| Waveform length |
4KSa |
| Frequency |
Accuracy |
100 ppm (<10 kHz) 50 ppm (>10 kHz) |
| Resolution |
0.1 Hz or 4 bits，take the greater one |
| Amplitude |
Output range |
10mV~7Vp-p (high impedance) |
| 5mV~3.5Vp-p (50Ω) |
| DC offset |
Range |
±3.5 V, high impedance |
| ±1.75 V, 50 Ω |
| Resolution |
100 μV or 3 bits, take the greater one |
| Accuracy |
2% (1 kHz) |
| Output impedance |
50 Ω |
| General specifications |
| Display |
Display type |
7” diagonal TFT liquid crystal |
| Display resolution |
800 (horizontal)*480 (vertical) pixels |
| Display colour |
16 million colours (24 bits true colour) |
| Persistence time |
minimum, 1 s, 5 s, 10 s, 30 s, infinite |
| Display type |
dot, vector |
| Display brightness |
adjustable |
| Grid type |
adjustable |
| Grid brightness |
adjustable |
| Interface |
Standard interface |
USB Host，USB Device |
| General specifications |
Probe compensator output |
| Output voltage, typical |
about 2Vpp input ≥1MΩ load |
| Frequency, typical |
1kHz |
| Power supply |
100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ |
| 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ |
| Power consumption |
<30W |
| Fuse |
T, 3.15A, 250V, 5x20mm |
| Operating temperature |
0~50 °C (32~122 °F) |
| Storage temperature |
-40~+71 °C (-40~159.8 °F) |
| Humidity |
≤+104℉(≤+40°C): ≤90% relative humidity |
| 106℉~122℉ (+41°C ~50°C): ≤60% relative humidity |
| Altitude |
Operating and nonoperating |
3, 000m (10, 000 feet) |
| Mechanical shock |
Random vibration |
0.31 g RMS from 50Hz to 500Hz, |
| 10 minutes on each axis |
| Nonoperating |
2.46g RMS from 5Hz to 500Hz, |
| 10 minutes on each axis |
| Operating |
50g, 11ms, half-sine wave |
| Mechanical |
Size |
318 x 110 x 150mm (length x width x height) |
| Weight |
1900g |
امین –
سلام چندتا پراب اسیلوسکوپ داره
مدیریت فروشگاه عصرتولز –
همان طور که در سایت شرکت و کاتالوگ محصول درج شده است:
دو عدد پراب bnc به سوسماری
یک عدد پراب اسیلوسکوپ
همراه دستگاه هست. توصیه می کنیم، ویدیو جعبه گشایی دستکاه را در صفحه محصول حتما مشاهده فرمایید.
توحید –
ببخشید یهو 400 گرون شد؟فک کنم چن روز پیش چک میکردم 13 تومن بود
محمد خالق پور –
سلام
آیا قیمت DSO-2C15 با DSO-2D15 مثل هم هستن؟ هر دوتا رو 13.4 زدید؟ قیمت ها بروز هستن؟
مدیریت فروشگاه عصرتولز –
سلام…
بله، قیمت ها بروز هستند.
سعید رنگین کمان –
اولا همراه دستگاه های سری جدید DSO-2D15 دو عدد پراب 150 عرضه میشه (گویا در سری های قبلی یک عدد پراب وجود داشته)! ثانیه مشکل هنگ کردن برطرف شده و نیاز به آپگرید وجود نداره (البته با وجود اینکه مشکلی نداشت بنده سیستم عامل رو به آخرین نسخه آپگرید کردم).
واقعا دستگاه خوبیه و به قیمتش می ارزه…